Portable two-channel digital oscilloscope with function generator/ arbitrary waveforms up to 25 MHz with 12-bit resolution and multimeter in one instrument. It features a large 2.8-inch TFT colour LCD display with 320x240 pixel resolution, built-in rechargeable battery, 70 MHz bandwidth, 250 MSa/s single-channel real-time sampling rate, intelligent battery charge control (after each 2-hour recharge, the device can be used continuously for an entire day or on standby for more than two months), auto-calibration function. The multimeter provides measurements of DC and AC voltage, DC and AC current, resistance, capacitance, diode test and continuity. PC software (downloadable) supports Windows 7 / 8 / 10 32-bit and 64-bit. Power supply via batteries or mains adapter.
 

• Number of Channels: 2
• Bandwidth: 70 MHz
• Horizontal
  - SEC/DIV Range: 5 ns/div~500 s/div 1, 2, 5 sequence
  - Real-time sampling rate: 250 MSa/s (single channel), 125 MSa/s (two channels)
  - Waveform interpolation: (sin x) / x
  - Record Length: Max. 6K for single channel; 3K for two channels
• Vertical
  - A/D Converter: 8 bit resolution, each channel sampled simultaneously
  - VOLTS/DIV Range: 10 mV/div~10 V/div BNC input
  - Bandwidth limit: 20 MHz typical
  - Low frequency response (-3db): ≤10Hz
  - Rise Time on BNC, typical: ≤5ns
  - DC Gain Accuracy: ± 3% for Normal or Average acquisition mode, 10 V/div to 10 mV/div
• Acquisition: Normal
• Trigger
  - Type: Edge
  - Modes: Auto, Normal, Single
  - Level: ± 4 divisions from centre of screen
  - Trigger Level Accuracy: 0.2div × volt/div within ± 4 divisions from centre of screen
  - Slope: Rising, Falling, Rising & Falling
  - Source: CH1/CH2
• Input
  - Coupling: DC, AC or GND
  - Input impedance, DC coupled: 25pF±3 pF, 1MΩ±2%
  - Probe attenuation: 1X, 10X
  - Probe attenuation factors supported: 1X, 10X, 100X, 1000X
  - Maximum input voltage: 150VRMS
• Measurements
  - Cursor: difference between voltage sliders: △V / difference between Time sliders: △T
  - Automatic measurements: frequency, amplitude

• Channels: 1
• Output waveform:
  -  Sine: 1 Hz-25 MHz
  - Square: 1 Hz- 10 MHz
  - Ramp: 1 Hz - 1 MHZ
  - EXP: 1 Hz - 5 MHz
• Sampling frequency: 250MSa/s 
• Amplitude: 2.5 Vpp (50 ohm) - 2.5 Vpp (high impedance)
• Frequency resolution: 0.1
• Waveform depth: 512Sa
• Vertical resolution: 12 bit
• Output impedance: 50 Ohm

• Multimeter (DMM):
  - Maximum display indication: 4000
  - Direct voltage: 400 mV / 4 V / 40 V / 400 V / 600 V
  - Alternating voltage: 4 V / 40 V / 400 V / 600 V
  - Continuous current: 40 mA / 200 mA / 4 A / 10 A
  - Alternating current: 40 mA / 400 mA / 4 A / 10 A
  - Resistance: 400 / 4 k / 60 k / 400 k / 4 Mega / 40 Mega 
  - Capacitance: 40 nF / 400 nF / 4 µF / 40 µF / 100 µF

• General Features
  -  Maximum display: 4000
  - Auto Range
  - Diode Test: Yes
  - Continuity Buzzer
  - Display: 2.8 inch TFT 64,000 colours, Resolution: 320x240 pixels, Contrast: Adjustable
  - Low battery indication
  - USB interface
  - Input impedance for: approx. 10 MΩ
  - Power supply: 2 rechargeable lithium batteries (18650 2600 mA - included) / mains adapter 230 VAC - 5 VDC - 2 A
  - Power consumption: <2.5 watts
  - Protection: 3A fuse
  - Working temperature: 0°C to +50°C
  - Weight: 624 grams
  - Casing colour: black
  - Dimensions (mm): 199x98x40 (L x W x H)
  - Weight: 624 g
   

• Accessories:
  - Mains adapter 230 VAC - 5 VDC - 2 A
  - Test leads
  - 2 Clip-on probes
  - USB-USB type C cable
  - BNC probe
  - Carrying case
  - Manual in English

• http://www.hantek.com/