Futura Group Srl
Stepper Motor Driver
Based on the Allegro A4988 chip, this driver is able to control a single bipolar stepper motor wit..
9.00€
SDcard shield for Arduino
Shield equipped with a slot for a micro SD Card, ideal for applications that require large storage c..
6.00€
IR38DM - IR receiver 38KHz
IR sensor tuned to 38KHz. Runs at 4.5V to 5.5V. Pin Out: Vdd= + 5 Vdc, GND..
1.90€
Video Overlay Shield for Arduino
Shield for Arduino based on the integrated LM1881 (National Semiconductors) which allows t..
15.50€
I2C bus - 7 segment display
One digit display for electronic applications. The kit use 10mm red leds. The display uses ..
999,999.00€
Bluetooth Evaluation Kit
Demoboard designed to test the module RN-42 or BSM2 that allows you to learn about the operation of ..
0.00€
Arduino/Raspberry Pi bridge
Designed to be used in combination with with Raspberry Pi (not included), this shield allows you to ..
22.50€
GPS antenna with U.FL connector
This is an embedded antenna for GPS. It has a IPX/U.FL connector, can be used SIM908, FT97..
7.85€
Starter Kit Raspberry PI
Contains everything you need to use Raspberry Pi: the widespread Embedded Linux platform. T..
999,999.00€
Raspberry Pi box - White
Tek-Berry housings represent such an optimized solution for a concrete type of a product, thus provi..
0.00€
Raspberry Pi box - Black
Tek-Berry housings represent such an optimized solution for a concrete type of a product, thus provi..
0.00€
Ethernet shield with W5100
This Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W..
22.00€
USB to TTL Serial Cable
The cable is easiest way ever to connect to your microcontroller/Raspberry Pi a serial console port...
5.90€
Module 1 relay (mounted)
Module with one relay to easy control your devices. Power: 5 Vdc Relays¨..
4.50€
Module 2 relays (mounted)
Module with two relays to easily control your devices. It has optoisolated inputs and status LEDs..
5.00€
Module 4 relays (mounted)
Module with four relays to easily control your devices. It has optoisolated inputs and status LED..
8.00€
Raspberry Pi shield for dummies
Experimental board analog / digital, which is designed to start using Raspberry Pi. The AD / DA..
16.00€
Multifunctional GSM alarm with SIM900
It’s small but packed with features. This GSM alarm sports a PIR motion sensor, can be battery..
99,999.00€
Extruder - Hot-end set 3mm
Heating section for 3D printer not assembled. Includes: 1 Pcs extruder brass heaterblock, 1 ..
0.00€
NTC 100K for 3D printer
NTC thermistor 100 kohm indicated for the measurement of temperatures up to 250 ° C. Ideal for d..
4.95€
Heated plate for 3D printer
Improve your 3D printer with this heated plate able to reach a temperature of 90..
0.00€
Extrusion set for 3D printer
Includes everything you need to build the body of the extruder 3D printer 3Drag. Includes all scr..
39.50€
Heater 12V 33W
Heater for extruder body. Power supply: 12÷15V, power: 33 watt, 6.8 ohm resistance, body diam..
0.00€
Kapton tape - 55MM/33M
Roll of Kapton tape, 55 mm high and 33 meters long. Used as thermal insulation (from -269 ° C to..
16.20€
